Accessories
 
EtherCAT Accessories

Accessories

Connectors

Ordering information Description Pict.
ZS1090-0003 EtherCAT/Ethernet RJ 45 connector, IP 20, 4-pin, for field-assembly
A
ZS1090-0005 EtherCAT/Ethernet RJ 45 plug, IP 20, 8-pin, field assembly
B
A
ZS1090-0003
B
ZS1090-0005
 

Cables

Ordering information Description
ZB9010 Industrial Ethernet/EtherCAT cable, fixed installation, CAT 5e,
4 wires
ZB9020 Industrial Ethernet/EtherCAT cable, drag chain suitable, CAT 5e, 4 wires
ZB903x Industrial Ethernet/EtherCAT cable, fixed installation, AWG26, CAT 5e, 4 wires

Fibre-optic cables for EK1501, EK1521, CU1521, CU1521-0010
(multimode 50/125 µm)

Ordering information Description
ZK1091-1001-0001 fibre-optic duplex cable, SC connector, 1 m
ZK1091-1001-0005 fibre-optic duplex cable, SC connector, 5 m
ZK1091-1001-0010 fibre-optic duplex cable, SC connector, 10 m

Further lengths and variants on request

POF cable for EK1541, EK1561, CU1561

Ordering information Description
Z1190 Fibre-optic duplex cable 980/1000 µm for direct connector assembly, sold by metre, PUR, 2-wire, for POF, drag-chain suitable, red
ZS1090-0008 Connector set for direct connector assembly for POF cables, contains 10 connectors and 1 polishing set including sanding gauge and polishing paper

Patch cable

The pre-assembled Ethernet/EtherCAT cables with RJ 45 plug enable fast, easy wiring inside the control cabinet and are suitable for short distances on the machine. The robust, industrial quality PUR cables distinguish themselves from office cables by both their mechanical and their EMC characteristics. Further lengths and variants on request.

Technical data ZK1090-9191-0001
Cross-section 4 x 2 x AWG26/7…4 x 2 x 0.128 mm²
Cable sheath material PUR
Colour green (RAL 6018)
Line configuration SF/UTP
Diameter sheath: typ. 5.9 mm ±0.2 mm
Bending radius > 5 x diameter
Category/class CAT5, class D
Operating/installation temp. -40…+75 °C/-10…+60 °C
Insertion cycles min. 750
Ordering information Cable
ZK1090-9191-0001 Industrial Ethernet/EtherCAT patch cable, 0.17 m
ZK1090-9191-0002 Industrial Ethernet/EtherCAT patch cable, 0.26 m
ZK1090-9191-0005 Industrial Ethernet/EtherCAT patch cable, 0.5 m
ZK1090-9191-0010 Industrial Ethernet/EtherCAT patch cable, 1.0 m
ZK1090-9191-0020 Industrial Ethernet/EtherCAT patch cable, 2.0 m
ZK1090-9191-0030 Industrial Ethernet/EtherCAT patch cable, 3.0 m
ZK1090-9191-0050 Industrial Ethernet/EtherCAT patch cable, 5.0 m
ZK1090-9191-0100 Industrial Ethernet/EtherCAT patch cable, 10.0 m
ZK1090-9191-0150 Industrial Ethernet/EtherCAT patch cable, 15.0 m
ZK1090-9191-0200 Industrial Ethernet/EtherCAT patch cable, 20.0 m
ZK1090-9191-0250 Industrial Ethernet/EtherCAT patch cable, 25.0 m
ZK1090-9191-0300 Industrial Ethernet/EtherCAT patch cable, 30.0 m
ZK1090-9191-0350 Industrial Ethernet/EtherCAT patch cable, 35.0 m
ZK1090-9191-0400 Industrial Ethernet/EtherCAT patch cable, 40.0 m
ZK1090-9191-0450 Industrial Ethernet/EtherCAT patch cable, 45.0 m
ZK1090-9191-0500 Industrial Ethernet/EtherCAT patch cable, 50.0 m
ZK1090-9191-0xxx
 

Connectors for KS Bus Terminals, ES EtherCAT Terminals

Ordering information Description
ZS2010 10 connectors for KS and ES series, spare part (KS/ES terminals are supplied with connector.)

Connectors for KM and EM modules

Ordering information Description
ZS2001-0001 connector for KM or EM module, 1-pin, without LED; spare part (KM and EM terminals are supplied with connector.)
ZS2001-0002 connector for KM or EM module, 1-pin, with LED; spare part
(KM and EM terminals are supplied with connector.)
ZS2001-0004 connector for KM or EM module, 3-pin, with LED; spare part
(KM and EM terminals are supplied with connector.)
ZS2001-0005 connector for KM module, 1-pin, without LED, labelling (1…10); spare part (KM and EM terminals are supplied with connector.)

Shielding connection system

The shielding connection system enables the shielding to be located very close to the terminals of the shielded line, so that interference is reduced to a minimum. Two variants are available for the realisation of this function: a shield busbar for attachment to a mounting rail or a bracket for separate mounting in the control cabinet.

Ordering information Shield busbar with mounting rail holder Pict.
ZB8500 clamp strap for shield connection with knurled screw,
width 11 mm, shield diameter max. 8 mm, packing unit = 10
A
ZB8510 shield busbar 10 x 3 mm, 1000 mm galvanised Cu,
packing unit = 1
B
ZB8520 mounting rail holder for shield busbar (10 x 3 mm),
packing unit = 2
C
ZB8530 U-clamp terminal up to 4 mm² for PE connection to the rail
(10 x 3 mm), packing unit = 20
Ordering information Shield busbar clamps Pict.
ZB8500 clamp strap for shield connection with knurled screw,
width 11 mm, shield diameter max. 8 mm, packing unit = 10
A
ZB8511 shield busbar clamp 10 x 3 mm for 5 Bus Terminals/EtherCAT Terminals 12 mm, packing unit = 10
D
ZB8530 U-clamp terminal up to 4 mm² for PE connection to the rail
(10 x 3 mm), packing unit = 20
A
ZB8500
B
ZB8510
C
ZB8520
D
ZB8511
 

Assembly aids

Ordering information Description
ZB8700 slot screwdriver
assembly tool for pressing the spring force clamps on the Bus Coupler and the Bus Terminals

Bus system housing

The BG1558 and BG1559 housings are especially suitable for the construction of compact I/O stations with a higher protection class (IP 65). The housings are supplied with mounting rails. If desired, the housings can be supplied fully fitted with EtherCAT Terminals, flanges and PG threaded fittings. Further sizes are available on request.

Ordering information Description Pict.
BG1558 bus system housing 400 mm x 200 mm x 120 mm (W x H x D) with mounting rail and holes
A
BG1559 bus system housing 600 mm x 200 mm x 120 mm (W x H x D) with mounting rail and holes  
A
BG1558
BG1558
 

Marking material

The EtherCAT Terminals can be individually labelled with standard contact signs. The marking material is not included in the EtherCAT Terminal delivery.
Contact label overview

Slide-in label cover, transparent

The slide-in label covers BZ3200 enable clear labelling of the individual channels or text-based functional description of the EtherCAT Terminals. The labels are inserted in the designated slots. For connecting the individual channels the label cover can be tilted upwards.

Ordering information Description
BZ3200 insertable label cover, transparent, pluggable, 11.5 mm x
104.5 mm, packing unit = 50
BZ5100 push-in strips for labels, A4 sheet, 160 pieces, pre-punched, packing unit = 10
Slide-in label cover
 

Coding pins and sockets for KS and ES terminals

The coding pins and sockets for ZS2010 and KS/ES terminals with pluggable wiring level enable coding between terminal and plug in order to prevent incorrect plug insertion.

Ordering information Description
ZS2010-0010 The set contains 100 sockets and 100 pins.
ZS2010-0010
ZS2010-0010
 

Demokit

The TC9910-B11x EtherCAT demokit offers a quick introduction into EtherCAT communication. It includes EtherCAT Terminals and a Coupler for testing simple I/O functions. The enclosed CD contains a step-by-step guide and a full version of TwinCAT as programming environment for the Beckhoff EtherCAT master. EtherCAT slaves of any type can be tested with this field-proven EtherCAT master. It also includes a comprehensive help collection that facilitates familiarisation with Beckhoff ADS communication and programming according to IEC 61131.

The demokit consists of:

Ordering information Description
TC9910-B110 EtherCAT demokit, with TwinCAT PLC license
TC9910-B111 EtherCAT demokit, without TwinCAT PLC license